View B140HTN011_7757576.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

pa ge 1 of 33 pro duct specification au optronics corporation b140htn01.1 document version : 1.0 ( ) preliminary specifications ( v ) final specifications module 14.0? fhd 16:9 color tft-lcd with led backlight design mo del name b140htn01.1 (h/w:0a) no te ( ) l ed backlight with driving circuit design cu stomer date ch ecked & approved by date no te: this specification is subject to change without notice. ap proved by date jo nken fan 07 /22/2013 pr epared by date am anda hj liao 07 /22/2013 nb bu marketing division au optronics corporation www.yslcd.com.tw
pag e 2 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 con tents 1. h andling precautions....................................................................................... 4 2. general description.......................................................................................... 4 2.1 general specification......................................................................................................... 4 2.2 optical characteristics ....................................................................................................... 4 3. functional block diagram................................................................................ 4 4. absolute maximum ratings............................................................................. 4 4.1 absolute ratings of tft lcd module ............................................................................... 4 4.2 absolute ratings of environment....................................................................................... 4 5. electrical characteristics................................................................................. 4 5.1 tft lcd module ............................................................................................................... 4 5.2 backlight unit..................................................................................................................... 4 6. signal interface characteristic ........................................................................ 4 6.1 pixel format image............................................................................................................ 4 6.2 integration interface requirement ..................................................................................... 4 6.3 interface timing ................................................................................................................. 4 6.4 power on/off sequence ................................................................................................. 4 7. panel reliability test........................................................................................ 4 7.1 vibration test ..................................................................................................................... 4 7.2 shock test ......................................................................................................................... 4 7.3 reliability test .................................................................................................................... 4 8. mechanical characteristics ............................................................................. 4 8.1 lcm outline dimension..................................................................................................... 4 9. shipping and package ..................................................................................... 4 9.1 shipping label format....................................................................................................... 4 9.2 carton package ................................................................................................................. 4 9.3 shipping package of palletizing sequence ....................................................................... 4 10. appendix: edid description .......................................................................... 4 www.yslcd.com.tw
pag e 3 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 rec ord of revision ver sion and date page old description new description remark 0.1 2013/01/28 all first edition for customer 0.2 2013/04/23 19 pin assignment pin assignment pi n no. 24/25 change 21 timing characteristics timing characteristics cl ock frequency modify vertical & horizontal section modify 5 & 6 general specification general specification pi exls h x v color / chromaticity coodinates 26 & 27 lcm outline dimension lcm outline dimension update outline data 0.3 2013/05/22 30 ~ 33 edid description edid description 0.4 2013/07/01 30 ~ 33 edid description edid description data change 1.0 2013/07/22 all preliminary specifications final specifications www.yslcd.com.tw
pag e 4 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 1. h andling precautions 1) since front polarizer is easily damaged, pay attention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an enclosure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) small amount of materials having no flammability grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source (iec60950 or ul1950), or be applied exemption. 13) disconnecting power supply before handling lcd modules, it can prevent electric shock, do not touch the electrode parts, cables, connectors and led circuit part of tft module that a led light bar build in as a light source of back light unit. it can prevent www.yslcd.com.tw
pag e 5 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 2. gen eral description b140htn01.1 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and led backlight system. the screen format is intended to support the 16:9 fhd, 1920(h) x1080(v) screen and 262k colors (rgb 6-bits data driver) with led backlight driving circuit. all input signals are edp(embedded displayport) interface compatible. b140htn01.1 is designed for a display unit of notebook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 co ndition: items unit specifications scre en diagonal [mm] 354.69 acti ve area [mm] 309.14x173.89 pix els h x v 1920x3(rgb) x 1080 pix el pitch [mm] 0.161x0.161 pix el format r.g.b. island disp lay mode normally white whi te luminance (i led =22ma) (note: iled is led current) [cd/m ] 350 typ. (5 points average) 298 min. (5 points average) lum inance uniformity 1.25 max. (5 points) con trast ratio 500 typ resp onse time [ms] 8 typ / 16 max nom inal input voltage vdd [volt] +3.3 typ. pow er consumption [watt] 6.5 max. (include logic and blu power) wei ght [grams] 270 max. mi n. typ. max. len gth 319.9 320.4 320.9 wid th 204.6 205.1 205.6 phy sical size include bracket [mm ] thickness - - 3.0 ele ctrical interface 2 lane edp gla ss thickness [mm] 0.4 sur face treatment glare, hardness 3h sup port color 262k colors ( rgb 6-bit ) www.yslcd.com.tw
pag e 6 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 tem perature range operating storage (non-operating) [ o c] [ o c] 0 to +50 -20 to +60 roh s compliance rohs compliance 2.2 op tical characteristics the optical characteristics are measured under stable conditions at 25 (ro om temperature) : item symbol con ditions min. typ. max. unit note whi te luminance i led =20ma 5 points average 298 350 - cd/m 2 1, 4, 5. ? r ? l h orizontal (right) cr = 10 (left) 40 40 45 45 - - degree vie wing angle ? h ? l vertical (upper) cr = 10 (lower) 10 30 15 35 - - 4, 9 lum inance uniformity ? 5p 5 points - - 1.25 1, 3, 4 lum inance uniformity ? 13p 13 points - - 1.60 2, 3, 4 con trast ratio cr 400 500 - 4, 6 cro ss talk % 4 4, 7 res ponse time t rt rising + falling - 8 16 msec 4, 8 rx 0 .590 0.620 0.6 50 red ry 0.320 0.350 0.3 80 gx 0 .290 0.320 0.3 50 gre en gy 0.570 0.600 0.6 30 bx 0 .120 0.150 0.1 80 blu e by 0.080 0.110 0.1 40 wx 0 .283 0.313 0.3 43 col or / chromaticity coodinates whi te wy 0.299 0.329 0.3 59 nts c % cie 1931 - 60 - 4 www.yslcd.com.tw
pag e 7 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 not e 1 : 5 points position (ref: active area) 1 2 3 4 5 h /4 h /4 h /4 h /4 h w w /4 w /4 w /4 w /4 not e 2 : 13 points position (ref: active area) w /4 w w /4 h h /4 h /4 h /4 h /4 7 9 1 0 w /4 1 8 w /4 1 0 1 0 1 0 1 0 2 3 1 3 1 2 4 5 6 1 1 note 3 : the luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the minimum test point luminance note 4 : measurement method the lcd module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measurement should be executed after lighting w13 = maximum brightness of thirteen points minimum brightness of thirteen points ma ximum brightness of five p oi nt s w5 = minimum brightness of five points www.yslcd.com.tw
pag e 8 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 bac klight for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen. not e 5 de finition of average luminance of white (y ): measure the luminance of gray level 63 at 5 points = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the point x at figure in note (1). note 6 de finition of contrast ratio: contrast ratio is calculated with the following formula. note 7 de finition of cross talk (ct) ct = | y b ? y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2) cen ter of the screen tft - lcd module 50 cm pho to detector lcd panel fie ld=2 con tra st ratio (cr)= b ri gh tne ss on the ?white? state b ri gh tne ss on the ?black? state www.yslcd.com.tw
pag e 9 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 not e 8 : definition of response time: the output signals of bm-7 or equivalent are measured when the input signals are changed from ?black? to ?white? (falling time) and from ?white? to ?black? (rising time), respectively. the response time interval between the 10% and 90% of amplitudes. refer to figure as below. s i g n a l ( r e l a t i v e v a l u e ) "bl ack" tr tf "wh ite" "white" 0% 10% 90% 100% www.yslcd.com.tw
pag e 10 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 not e 9 . definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). the 180 viewing angle range is broken down as follows; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. www.yslcd.com.tw
pag e 11 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 3. f unctional block diagram the following diagram shows the functional block of the 14.0 inches wide color tft/lcd 30 pin tft -lcd 1920*(3)*1080 pixels www.yslcd.com.tw
pag e 12 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 4. a bsolute maximum ratings an absolute maximum rating of the module is as following: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions log ic/lcd drive voltage vin -0.3 +4.0 [volt] note 1,2 4.2 a bsolute ratings of environment item symbol min max unit conditions ope rating temperature top 0 +50 [ o c] note 4 ope ration humidity hop 5 95 [%rh] note 4 sto rage temperature tst -20 +60 [ c] note 4 sto rage humidity hst 5 95 [%rh] note 4 not e 1: at ta (25 ) no te 2: permanent damage to the device may occur if exceed maximum values note 3: led specification refer to section 5.2 note 4: for quality performance, please refer to auo iis (incoming inspection standard). twb= 39c ope rating range storage range www.yslcd.com.tw
pag e 13 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 5. el ectrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; the power specification are measured under 25 and frame frenquency under 60hz symble parameter min typ max units note vdd logic/lcd drive volta g e 3.0 3.3 3.6 [volt] pdd vdd power - - 1.0 [watt] note 1 idd idd current - - 303 [ma] note 1 i rus h inrush current - - 2000 [ma] note 2 vdd rp allowable logic/lcd drive ripple voltage - - 100 [mv] p-p not e 1 : maximum measurement condition bla ck pattern at 3.3v driving voltage. (p max =v 3.3 x i black ) typical measurement condition : mosaic patte note 2 mea sure condition 90% 10% vi n rising time 0v 3.3v 0. 5 ms www.yslcd.com.tw
pag e 14 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 5.1 .2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. signal electrical characteristics are as follows; display port main link signal: dis play port main link min typ max unit vcm rx input dc common mode voltage 0 2 v vdi ff p-p peak-to-peak voltage at a receiving device 120 mv fal low as vesa display port standard v1.1a www.yslcd.com.tw
pag e 15 of 33 prod uct specification au optronics corporation b140htn01.1 document version : 1.0 dis play port aux_ch signal: dis play port aux_ch min typ max uni t vcm aux dc common mode voltage 0 2 v vdi ff p-p aux peak-to-peak voltage at a receiving device 0.32 1. 36 v fal low as vesa display port standard v1.1a. display port v hpd signal: display port v hpd min typ max unit v hpd hpd voltage 2 v fal low as vesa display port standard v1.1a. www.yslcd.com.tw
pa g e 16 of 33 au optronics corporation pro duct specification b1 4 0htn01.1 document version : 1.0 5.2 backlight unit 5.2.1 led characteristics parameter symbol min typ max units condition bac klight power consumption pled - - 3.5 [watt] (ta=25 ), note 1 vin =12v led life-time n/a 15,000 - - hour (ta=25 ), note 2 i f =23 ma note 1: 21 3 1ldp21 32dp2ppn2 n 222dpa1 2notlpo3lodn222dpa1 2notlpo3lodn22oon:2 note 2: 2u2n2 oloa2on21t2l2tloa1l2loa2ld22p11lodn2d2onolo1 2 3aond3t2 5.2.2 backlight input signal characteristics parameter symbol min typ max units remark led power supply vled 6.0 12.0 21.0 [volt] led enable input high level 2.5 - 5.5 [volt] led enable input low level vled_en - - 0.5 [volt] pwm l ogic input high level 2.5 - 5.5 [volt] pwm l ogic input low level vpwm_ en - - 0.5 [volt] pwm in put frequency fpwm 200 1k 10k hz pwm d uty ratio duty 5 -- 100 % define as connector interface (ta=25 ) note 1 : 2daan2t:tla2e3 23edn2ptotldp2nd2op2l1n2ida2 2 www.yslcd.com.tw
pa g e 17 of 33 b140htn01.1 document version : 1.0 au optronics corporation prod uct specification 6. signal interface characteristic 6.1 pixel format image following figure shows the relationship of the input signals and lcd pixel format. www.yslcd.com.tw
pa g e 18 of 33 b140htn01.1 document version : 1.0 au optronics corporation prod uct specification 6.2 integration interface requirement 6.2.1 connector description physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for signal connector man ufacturer ipex or compatible typ e / part number i-pex jp co.,ltd;20455-030e-12 mat ing housing/part number ipex 20453-030t-01 or compatible www.yslcd.com.tw
pa g e 19 of 33 b140htn01.1 document version : 1.0 au optronics corporation prod uct specification 6.2.2 pin assignment (2 lane) edp lane 2ot212opnlo1 2ton1 2lnd d:2dp2n2onlp121n2o2te21l12lp1ntp2o2 2 pin no sym bol fu nction 1 n c 2 h_g nd hig h speed ground 3 lan e1_n com p signal link lane 1 4 lan e1_p tru e signal link lane 1 5 h _gnd high speed ground 6 l ane0_n comp signal link lane 0 7 l ane0_p true signal link lane 0 8 h _gnd high speed ground 9 a ux_ch_p true signal auxiliary ch. 10 aux_ch_n comp signal auxiliary ch. 11 h_gnd high speed ground 12 lcd_vcc lcd logic and driver power 13 lcd_vcc lcd logic and driver power 14 lcd self test lcd panel self test enable 15 lcd_gnd lcd logic and driver ground 16 lcd_gnd lcd logic and driver ground 17 hpd hpd signale pin 18 bl_gnd backlight ground 19 bl_gnd backlight ground 20 bl_gnd backlight ground 21 bl_gnd backlight ground 22 bl_enable backlight on / off 23 bl_pwm_dim system pwm signal input 24 nc nc 25 nc nc 26 bl_pwr backlight power 27 bl_pwr backlight power 28 bl_pwr backlight power 29 bl_pwr backlight power 30 nc no connect www.yslcd.com.tw
pa g e 20 of 33 b140htn01.1 document version : 1.0 au optronics corporation prod uct specification not e1: 2l1pl2pda2pol2to2 note2: 2ne3l2ton1 t2t1 22 d2dp2ooae1n2tl1l2n2nn2ot2d2 2 2 2 2 2 2 nlpn1 2op3ol2d edp inputs 21p21t2d don pin 30 connector pin 1 3. lane0- 4. lane0+ 6. lane1- 7.lane1+ www.yslcd.com.tw
pa g e 21 of 33 b140htn01.1 document version : 1.0 au optronics corporation prod uct specification 6.3 interface timing 6.3.1 timing characteristics basically, interface timings should match the 1920x1080 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit fra me rate - - 60 - hz clo ck frequency 1/ t clock 66.6 70 75 mhz per iod t v 1108 1110 1480 act ive t vd 1080 ver tical section blanking t vb 8 30 400 t line per iod t h 2040 2010 3072 act ive t hd 1920 hor izontal sec tion blanking t hb 120 180 1152 t clock not e 1 : u21d2ot21t2deloao2tllon2 note 2 : u2a1soa3a2 di2p3n:2222p www.yslcd.com.tw
pa g e 22 of 33 b140htn01.1 document version : 1.0 au optronics corporation prod uct specification 6.4 power on/off sequence display port panel power sequence: dis play port aux_ch transaction only: www.yslcd.com.tw
pa g e 23 of 33 b140htn01.1 document version : 1.0 au optronics corporation prod uct specification display port panel power sequence timing parameter: not e1: the sink must include the ability to generate black video autonomously. the sink must automatically enable black video under the following conditions: -upon lcdvdd power on (with in t2 max)-when the "novideostream_flag" (vb-id bit 3) is received from the source (at the end of t9). -when no main link data, or invalid video data, is received from the source. black video must be displayed within 64ms (typ) from the start of either condition. video data can be deemed invalid based on msa and timing information, for example. note 2: the sink may implement the ability to disable the black video function, as described in note 1, above, for system development and debugging purpose. note 3: the sink must support aux_ch polling by the source immediately following lcdvdd power on without causing damage to the sink device (the source can re-try if the sink is not ready). the sink must be able to respond to an aux_ch transaction with the time specified within t3 max. www.yslcd.com.tw
pa g e 24 of 33 b140htn01.1 document version : 1.0 au optronics corporation prod uct specification display port panel b/l power sequence timing parameter: www.yslcd.com.tw
pa g e 25 of 33 b140htn01.1 document version : 1.0 au optronics corporation prod uct specification 7. panel reliability test 7.1 vibration test test spec: test method: non-operation acceleration: 1.5 g frequency: 10 - 500hz random sweep: 30 minutes each axis (x, y, z) 7.2 shock test test spec: test method: non-operation acceleration: 220 g , half sine wave active time: 2 ms pulse: x,y,z .one time for each side 7.3 reliability test items required condition note tem perature humidity bias ta= 40 , 90%rh, 300h hig h temperature operation ta= 50 , dry, 300h low temperature operation ta= 0 , 300h hig h temperature storage ta= 60 , 35%rh, 300h low temperature storage ta= -20 , 50%rh, 250h the rmal shock test ta=-20 to 60 , duration at 30 min, 100 cycles esd contact : 8 kv air : 15 kv note 1 note1: according to en 61000-4-2 , esd class b: some performance degradation allowed. self-recoverable. no data lost, no hardware failures. remark: mtbf (excluding the led): 30,000 hours with a confidence level 90% www.yslcd.com.tw
p a g e 26 of 33 b140 htn01.1 document version : 1.0 product specification a u o p tronics corporation 8 . m echanical characteristics 8.1 lcm outline dimension www.yslcd.com.tw
p a g e 27 of 33 b140 htn01.1 document version : 1.0 product specification a u o p tronics corporation note : prevention ic damage, ic positions not allowed any overlap over these areas. www.yslcd.com.tw
page 28 of 33 b140htn01.1 document version : 1.0 product specification au optronics corporation 9. shi pping and package 9.1 shipping label format mode l name hard ware code www.yslcd.com.tw
page 29 of 33 b140htn01.1 document version : 1.0 product specification au optronics corporation 9.2 car ton package 9.3 shipping package of palletizing sequence www.yslcd.com.tw
page 30 of 33 b140htn01.1 document version : 1.0 product specification au optronics corporation 10. ap pendix: edid description addr ess func tion valu e valu e valu e note hex hex bin dec 00 he ader 00 00000000 0 01 ff 1 1111111 255 02 ff 1 1111111 255 03 ff 1 1111111 255 04 ff 1 1111111 255 05 ff 1 1111111 255 06 ff 1 1111111 255 07 00 0 0000000 0 08 ei sa manuf. code lsb 06 00000110 6 09 co mpressed ascii af 10101111 175 0a prod uct code 3d 0 0111101 61 0b hex, lsb first 11 0 0010001 17 0c 32 -bit ser # 00 00000000 0 0d 00 0 0000000 0 0e 00 0 0000000 0 0f 00 0 0000000 0 10 we ek of manufacture 00 00000000 0 11 ye ar of manufacture 16 00010110 22 12 ed id structure ver. 01 00000001 1 13 ed id revision # 04 00000100 4 14 v ideo input def. (digital i/p, non-tmds, crgb) 95 1 0010101 149 15 m ax h image size (rounded to cm) 1f 00011111 31 16 ma x v image size (rounded to cm) 11 00010001 17 17 d isplay gamma (=(gamma*100)-100) 78 01111000 120 18 fe ature support (no dpms, active off, rgb, tmg blk#1) 02 00000010 2 19 re d/green low bits (lower 2:2:2:2 bits) 9f 10011111 159 1a bl ue/white low bits (lower 2:2:2:2 bits) e5 11100101 229 1b re d x (upper 8 bits) 96 10010110 150 1c re d y/ higher 8 bits 58 01011000 88 1d gr een x 53 01010011 83 1e gr een y 8a 10001010 138 1f bl ue x 26 00100110 38 20 b l ue y 24 00100100 36 21 w h ite x 50 01010000 80 22 w h ite y 54 01010100 84 www.yslcd.com.tw
page 31 of 33 b140htn01.1 document version : 1.0 product specification au optronics corporation 23 es tablished timing 1 00 00000000 0 24 es tablished timing 2 00 00000000 0 25 es tablished timing 3 00 00000000 0 26 st andard timing #1 01 00000001 1 27 01 0 0000001 1 28 st andard timing #2 01 00000001 1 29 01 0 0000001 1 2a st andard timing #3 01 00000001 1 2b 01 0 0000001 1 2c st andard timing #4 01 00000001 1 2d 01 0 0000001 1 2e st andard timing #5 01 00000001 1 2f 01 0 0000001 1 30 st andard timing #6 01 00000001 1 31 01 0 0000001 1 32 st andard timing #7 01 00000001 1 33 01 0 0000001 1 34 st andard timing #8 01 00000001 1 35 01 0 0000001 1 36 pi xel clock/10000 lsb b0 10110000 176 37 pi xel clock/10000 usb 36 00110110 54 38 ho rz active lower 8bits 80 10000000 128 39 ho rz blanking lower 8bits b4 10110100 180 3a ho rzact:horzblnk upper 4:4 bits 70 01110000 112 3b ve rtical active lower 8bits 38 00111000 56 3c ve rtical blanking lower 8bits 1e 00011110 30 3d ve rt act : vertical blanking (upper 4:4 bit) 40 01000000 64 3e ho rzsync. offset 30 00110000 48 3f ho rzsync.width 64 01100100 100 40 ve rtsync.offset : vertsync.width 31 00110001 49 41 ho rz&vert sync offset/width upper 2bits 00 00000000 0 42 ho rizontal image size lower 8bits 35 00110101 53 43 ve rtical image size lower 8bits ad 10101101 173 44 ho rizontal & vertical image size (upper 4:4 bits) 10 00010000 16 45 ho rizontal border (zero for internal lcd) 00 00000000 0 46 v e rtical border (zero for internal lcd) 00 00000000 0 47 s i gnal (non-intr, norm, no stero, sep sync, neg pol) 18 00011000 24 www.yslcd.com.tw
page 32 of 33 b140htn01.1 document version : 1.0 product specification au optronics corporation 48 de tailed timing/monitor 00 00000000 0 49 de scriptor #2 00 00000000 0 4a 00 0 0000000 0 4b 0f 0 0001111 15 4c 00 0 0000000 0 4d 00 0 0000000 0 4e 00 0 0000000 0 4f 00 0 0000000 0 50 00 0 0000000 0 51 00 0 0000000 0 52 00 0 0000000 0 53 00 0 0000000 0 54 00 0 0000000 0 55 00 0 0000000 0 56 00 0 0000000 0 57 00 0 0000000 0 58 00 0 0000000 0 59 20 0 0100000 32 5a de tailed timing/monitor 00 00000000 0 5b de scriptor #3 00 00000000 0 5c 00 0 0000000 0 5d fe 11111110 254 5e 00 00000000 0 5f ma nufacture 41 01000001 65 a 60 ma nufacture 55 01010101 85 u 61 ma nufacture 4f 01001111 79 o 62 0a 0 0001010 10 63 20 0 0100000 32 64 20 0 0100000 32 65 20 0 0100000 32 66 20 0 0100000 32 67 20 0 0100000 32 68 20 0 0100000 32 69 20 0 0100000 32 6a 20 0 0100000 32 6b 20 0 0100000 32 6c d e tailed timing/monitor 00 00000000 0 6d d e scriptor #4 00 00000000 0 6e 00 0 0000000 0 www.yslcd.com.tw
page 33 of 33 b140htn01.1 document version : 1.0 product specification au optronics corporation 6f fe 1 1111110 254 70 00 0 0000000 0 71 ma nufacture p/n 42 01000010 66 b 72 ma nufacture p/n 31 00110001 49 1 73 ma nufacture p/n 34 00110100 52 4 74 ma nufacture p/n 30 00110000 48 0 75 ma nufacture p/n 48 01001000 72 h 76 ma nufacture p/n 54 01010100 84 t 77 ma nufacture p/n 4e 01001110 78 n 78 ma nufacture p/n 30 00110000 48 0 79 ma nufacture p/n 31 00110001 49 1 7a ma nufacture p/n 2e 00101110 46 . 7b ma nufacture p/n 31 00110001 49 1 7c 20 0 0100000 32 7d 0a 0 0001010 10 7e ex tension flag 00 00000000 0 7f ch ecksum 88 10001000 136 www.yslcd.com.tw

▲Up To Search▲

Price & Availability of B140HTN011

	To Download B140HTN011 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .